![]() If you have more than one slave, they can each be set either way. All of the slaves will either be in sync or antisync to the master. When you have your Vortechs setup in master/slave configuration, all of the settings are done from the master Vortech. So if your Master Vortech is in reefcrest mode and it's current speed is 80%, the slave Vortech will also be in reefcrest mode but the speed will around 20% if it's antisync and 80% if it's sync. Anti-sync will make it run in the same mode as the master but the speed will be the opposite. ![]() and 50: Photo-electric cell 7094.In sync means that the unit will be running in the same mode at the same speed as the master.and 48: Functions of the Wavecontroller Wav.and 46: Double wave generation (4) In tanks.and 44: If the Nano Wavebox / Wavebox pump.and 42: Adjusting the wave frequency on the.and 40: Other power supply systems for Nano.and 38: Power supply units for Nano Wavebox.and 36: Initial operation with Wavecontroll.and 34: The Wavebox uses two Magnet Holder.and 32: Attachment of the Wavebox Fitting e.and 30: Attaching Nano Wavebox Mounting ela.and 28: Outlet, inlet and other components.and 26: Choice of location for the Wavecont.and 24: Choosing the position of the Wavebo.and 18: Safety instructions for Magnet Hold.and 16: Safety instructions Do not operate.and 14: The cabinet or the aquarium furnitu.and 12: Warning ! TUNZE® Nano Wavebox and.and 10: Technical data Nano Wavebox 6206 (1.and 8: A special Wavebox pump is used as a.and 6: General aspects TUNZE® Nano Wavebo.and 4: Table of Contents General aspects T.and 2: Nano Wavebox 6206 Wavebox 6215 Gebr.Si la hauteur de la vague n’est pas connue, positionnez le niveau d’eau (aquarium au repos) à 2 ou 3 cm en-dessous du bord supérieur (2) de la Nano Wavebox. Dans des aquariums de petite capacité, Nano Wavebox peut être complètement immergée. Afin de garantir une oscillation conséquente ainsi qu’un brassage circulaire, nous conseillons d’orienter sa sortie d’eau en direction de la longueur de l’aquarium. Placement Nano Wavebox Placez TUNZE® Nano Wavebox 6206 dans un coin de l’aquarium (1), veillez à la bonne tenue du support ! Nano Wavebox doit être parfaitement verticale sans être soumise à des soubresauts durant son fonctionnement. If the wave height is not known yet, the water level without waves should be about 2 to 3 cm below the upper edge of the Nano Wavebox (2). In case of smaller tanks, the Nano Wavebox can be immersed completely. For perfect wave formation and circular current, we recommend positioning the water outlet in the direction of the longitudinal axis of the aquarium. Ensure a secure fit ! Nano Wavebox should be fitted upright and should not move during operation. 20Ĭhoosing the position of the Nano Wavebox Place TUNZE® Nano Wavebox 6206 in any corner of the aquarium (1). ![]() 2- 3 cm unter dem oberen Rand der Nano Wavebox liegen (2). Wenn die Wellenhöhe noch nicht bekannt ist, so sollte der Wasserstand ohne Wellenbildung ca. Bei kleineren Becken kann die Nano Wavebox komplett eingetaucht werden. Für eine optimale Wellenbildung und Ringströmung empfehlen wir den Wasserausgang in Richtung der Längsachse des Aquariums zu orientieren. Auf festen Sitz achten! Nano Wavebox soll senkrecht stehen und darf sich beim Betrieb nicht bewegen. Platzwahl Nano Wavebox TUNZE® Nano Wavebox 6206 in eine beliebige Ecke des Aquariums aufstellen (1).
0 Comments
Leave a Reply. |